- 您现在的位置：买卖IC网 > Sheet目录221 > DMS-20PC-4/20B-C (Murata Power Solutions Inc)METER LED SELF-PWR 3.5DIG RED
DMS-20PC-4/20 Series
Subminiature 4-20mA Loop-Powered
3? Digit LED Process Monitors
3. Desired display readings are:
ON
Examples (DMS-20PC-4/20B-Bipolar Model)
4mA = ".000"
1. Desired display readings are:
ON
12mA = ".250"
1
2
3
4
5
6
4mA = "–1.00"
This example is not as straightforward as the previous two. Notice that
20mA = "1.00"
1
2
3
4
5
6
12mA is exactly halfway between 4mA and 20mA. If we assume that
the input could go up to 20mA, the display reading would then be: 2
x .250 or ".500". From Table 1 we can now select DIP-switch setting
#4 and enable DP1 via SW4. Apply 4mA and adjust R3 so the display
reads ".000". Apply 12mA and adjust R7 so the display
Use DIP-switch setting #5 in Table 2 and enable decimal point DP2 via
SW5. Apply 12mA and adjust R3 so the display reads "0.00". Apply
20mA and adjust R7 so the display reads "1.00". Apply 4mA and verify
that the display reads "–1.00", readjust R3 and R7 if necessary.
reads ".250".
2. Desired display readings are:
ON
DMS–20PC–4/20B (Bipolar Reading Model)
4mA = "–450"
20mA = "450"
1
2
3
4
5
6
The DMS-20PC-4/20B's zero-offset circuit differs from the unipolar 'S'
model described above in that with the 'B' model, a half-scale 12mA input
is normally set to display "000". Therefore, all of the of the DIP-switch
settings in Table 2 assume a reading of "000" is desired with a 12mA input.
Display readings other than those shown in Table 2 are possible, contact
DATEL for more information.
Use DIP-switch setting #2 in Table 2. Apply 12mA and adjust R3 so the
display reads "000". Apply 20mA and adjust R7 so the display reads
"450". Apply 4mA and verify that the display reads "–450". Repeat
adjustment procedure if necessary. For these display readings, no
decimal points are used. Set SW4, SW5 and SW6 to OFF.
When con?guring the DMS-20PC-4/20B for the ?rst time, or when select-
ing a new range, set both R3 and R7 fully clockwise (roughly 22 turns) to
3. Desired display readings are:
4mA = "–650"
ON
their minimum offset/minimum-span positions, respectively. Then select
20mA = "650"
1
2
3
4
5
6
the desired readings from Table 2 and con?gure DIP-switches SW1, SW2,
and SW3 accordingly.
The procedure below illustrates how to calibrate the DMS-20PC-4/20B
to its factory-calibrated readings of "–1000" with a 4mA input and "1000"
with a 20mA input. When performing DIP-switch settings, be sure the DIP-
switch's small actuators are ?rmly engaged in their fully-ON or fully-OFF
positions.
1. Set both R3 and R7 fully clockwise.
2. Select DIP-switch setting #1 from Table 2.
3. Apply a precision 12mA input and adjust R3 until the meter's display
reads "000".
4. Apply a precision 20mA input and adjust R7 until the meter's display
reads "1000".
5. Apply a precision 4mA input and the display should read "–1000".
Repeat steps 3 and 4 to make sure the two adjustments did not affect
one another.
Table 2. DMS-20PC-4/20B (Bipolar Model) DIP-Switch Settings
Notice that these readings can be obtained using either DIP-switch
setting #1 or DIP-switch setting #2 in Table 2. In situations like this
where DIP-switch settings overlap, less-sensitive R3/R7 adjustments
can be achieved if the higher DIP-setting # is selected (setting #2 in
this example). Apply 12mA and adjust R3 so the display reads "000".
Apply 20mA and adjust R7 so the display reads "650". Apply 4mA and
verify that the display reads "–650". Repeat adjustment procedure if
necessary.
DMS-20PC-4/20P (Positive Reading Model)
The DMS-20PC-4/20P’s Zero-Offset circuit is optimized to produce posi-
tive readings at both 4mA and 20mA input levels. As shown in Table 3’s
?rst three columns, a 4mA input can be typically adjusted (using R3, Zero/
Offset Adjust) to display any positive reading between “000” and “800”.
The corresponding 20mA-input reading is then added to the 4mA offset
as a differential whose magnitude is varied by adjusting R7 (Gain/Span
Adjust).
The ‘Differential Range’ column in Table 3 lists the nominal differential
display-readings which can be obtained with R7 at, or very close to, its
full-clockwise, minimum span position. The Differential Range column can
Display Reading
4mA
12mA
20mA
SW1
SW2
SW3
be used as a guide when con?guring the meter for the majority of user
applications. Higher differential ranges are obtainable; however, the use of
higher differential readings results in correspondingly-lower positive read-
1.
2.
3.
4.
5.
–600 to –1000
–350 to –650
–250 to –400
–150 to –250
–100 to –150
000
000
000
000
000
600 to 1000
350 to 650
250 to 400
150 to 250
100 to 150
Off
On
Off
Off
On
Off
Off
On
Off
On
Off
Off
Off
On
On
ings with 4mA inputs, that is, R3’s clockwise adjustment-range is reduced.
Example #3 below illustrates this concept. Please contact DATEL if there
is any doubt as to whether or not the DMS-20PC-4/20P can be con?gured
for your display readings requirements.
The ?rst step when con?guring the DMS-20PC-4/20P for the ?rst time, or
when selecting a new range, is to set R3 fully counterclockwise and R7
www.murata-ps.com/dpm
29 Mar 2011
email: sales@murata-ps.com
MPM_DMS20PC-4/20.C05 Page 3 of 6
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
DMS-20PC-7-DCM-C
DPM LED SELF-POWERED DC RED
DMS-20RM-3-DC2-R-C
AC VOLTMETER 300V RANGE DC POWER
DMS-30DR-1-R-C
DPM LED 2V 3.5DIG DAYLIGHT RED
DMS-30LCD-1-9-C
DPM LCD 2VDC 3.5DIG 9-14V SUPPLY
DMS-30LCDA-4/20S-C
METER LCD SELF-POWERED 3.5DIG
DMS-30PC-1-RH-C
DPM LED MINI 2VDC SUPER-BRIGHT
DMS-30PC-4/20S-24GS-I-C
DPM LED 24V SUPPLY 3.5DIG GREEN
DMS-40LCD-0/1-5-C
DPM LCD 200MV/2VDC 4.5DIGIT
相关代理商/技术参数
DMS-20PC-4/20P
功能描述:数字面板表 3 1/2 digit red LED Positive reading RoHS:否 制造商:Murata Power Solutions 设备类型:AC Voltmeters 显示器类型:LED, 3 Digit, Red 工作电源电压:85 VAC to 264 VAC 工作电源电流:50 mArms 输入电流:50 mA 输入频率: 输入电压:120 VAC 系列:DMS-20PC-1-LM
DMS-20PC-4/20P-C
功能描述:数字面板表 20mA max 4.5 V drop Pos read 3 1/2 LED RoHS:否 制造商:Murata Power Solutions 设备类型:AC Voltmeters 显示器类型:LED, 3 Digit, Red 工作电源电压:85 VAC to 264 VAC 工作电源电流:50 mArms 输入电流:50 mA 输入频率: 输入电压:120 VAC 系列:DMS-20PC-1-LM
DMS-20PC-4/20S
功能描述:数字面板表 3.5 Digit Loop Meter +4 To +20mA RoHS:否 制造商:Murata Power Solutions 设备类型:AC Voltmeters 显示器类型:LED, 3 Digit, Red 工作电源电压:85 VAC to 264 VAC 工作电源电流:50 mArms 输入电流:50 mA 输入频率: 输入电压:120 VAC 系列:DMS-20PC-1-LM
DMS-20PC-4/20S-C
功能描述:数字面板表 3.5 Digit Loop Meter +4 To +20mA RoHS:否 制造商:Murata Power Solutions 设备类型:AC Voltmeters 显示器类型:LED, 3 Digit, Red 工作电源电压:85 VAC to 264 VAC 工作电源电流:50 mArms 输入电流:50 mA 输入频率: 输入电压:120 VAC 系列:DMS-20PC-1-LM
DMS-20PC-4-DCM
功能描述:数字面板表 - DC Voltage Monitor -4.50 to -19.99Vdc RoHS:否 制造商:Murata Power Solutions 设备类型:AC Voltmeters 显示器类型:LED, 3 Digit, Red 工作电源电压:85 VAC to 264 VAC 工作电源电流:50 mArms 输入电流:50 mA 输入频率: 输入电压:120 VAC 系列:DMS-20PC-1-LM
DMS-20PC-4-DCM-C
功能描述:数字面板表 - DC Voltage Monitor -4.50 to -19.99Vdc RoHS:否 制造商:Murata Power Solutions 设备类型:AC Voltmeters 显示器类型:LED, 3 Digit, Red 工作电源电压:85 VAC to 264 VAC 工作电源电流:50 mArms 输入电流:50 mA 输入频率: 输入电压:120 VAC 系列:DMS-20PC-1-LM
DMS-20PC-5-DCM
功能描述:数字面板表 - DC Voltage Monitor -18.0 to -50.0Vdc RoHS:否 制造商:Murata Power Solutions 设备类型:AC Voltmeters 显示器类型:LED, 3 Digit, Red 工作电源电压:85 VAC to 264 VAC 工作电源电流:50 mArms 输入电流:50 mA 输入频率: 输入电压:120 VAC 系列:DMS-20PC-1-LM
DMS-20PC-5-DCM-C
功能描述:数字面板表 - DC Voltage Monitor -18.0 to -50.0Vdc RoHS:否 制造商:Murata Power Solutions 设备类型:AC Voltmeters 显示器类型:LED, 3 Digit, Red 工作电源电压:85 VAC to 264 VAC 工作电源电流:50 mArms 输入电流:50 mA 输入频率: 输入电压:120 VAC 系列:DMS-20PC-1-LM